Mira Event XS Thermostatic Power Shower
The thermostatic model gives you all the Mira Event XS features, plus a number of extra benefits.
- Easy-clean Mira Logic power showerhead with four exciting spray patterns - Start, Champagne, Massage and Eco
- Separate temperature and flow controls allow you to leave the temperature control at your preferred setting
- Thermostatic control prevents sudden temperature changes, to give a consistent, enjoyable showering experience
- Overrideable maximum temperature stop, for a hotter shower
- Easy-to-use push-button start/stop
- Flow boost for a progressive increase of spray from economy to full flow
- Greater flow rate of up to 16 litres per minute
Description
- An all in one power shower with an integral 230V / 240V AC pump and mixer assembly.
- Independent spray force and temperature selection controls
- 15mm dual entry push-fit inlet connections
- Patented pump design removes the need for priming under recommended installation conditions
- Integral inlet filters and check valves
- Cover, case and internal assemblies moulded from engineering plastics and polymers
Manual Version
- Independent temperature and outlet flow controls
- Maximum temperature stop
- Generates flow of up to 14 l/min and 0.7 bar
Thermostatic Version
- Thermostatic temperature control system
- Push button Start / Stop
- Over rideable maximum temperature stop (may be disabled)
- Progressive increase of spray force from an economical standard flow to full flow with rotation of the flow control knob
- Generates flow of up to 16 l/min at 0.7 bar
Product Range
Mira Event XS and Mira Event XS Thermostatic
Surface mounted all in one power shower for connection to exposed pipework and operation with gravity fed supplies
Supplied complete with a metal clad shower hose, clamp bracket, slide bar, wall mounted soap dish, hose retaining ring / gel hook and Mira Logic Power showerhead with four different spray modes (Star, Champagne, Massage and Eco).
Limitations of Use
- The Mira Event XS must not be connected to a mains fed water supply
- The Mira Event XS is not suitable for installation in institutional / commercial applications
- The powerful pump motor is fitted on rubber isolation mounts to reduce the transmitted sound levels. The type of wall surface will affect the perceived sound levels.
- The Mira Event XS should not be used for applications where an outlet flow controls forms part of the shower fitting.
- The product and its components are only suitable for normal water supplies and should be cleaned only with mild washing up detergent or soap solution.
Temperature
Manual Version
- Manual (non thermostatic) control system
- Maximum recommended hot water temperature : 65°C
Thermostatic Version
- Wax capsule temperature control system
- Automatic shutdown if cold supply fails
- Over rideable maximum temperature stop
- Temperature control range : 35°C - 45°C
Pressure
- Minimum maintained pressure : 0.008 bar min (80mm)
- Maximum maintained pressure : 0.5bar
- Maximum static pressure : 1.0 bar
- Maximum pressure loss ratio : 10:1
Performance
The specification performance outlined below for the standard appliance is achieved with a blend set between 35°C - 45°C and supplies of 15°C cold and 65°C hot with nominally equal pressures
Thermostatic Version
- The blended water temperature is maintained within 1°C with a 10°C change in the hot or cold water supply
- The thermostat effects a shut down in approximately 2 seconds if the cold supply fails.
- Shut down is achieved only if the hot supply is a minimum of 12°C above the blend temperature
- The blended water temperature is maintained within 1.5°C when the pressure between inlet and outlet is halved (defined as a pressure los ratio of 2:1) on either the hot or cold side.
- Temperature overshoot will not exceed 50°C when adjusting the blend temperature from full cold to full hot.
Guarantee
Guaranteed for one year from date of purchase against faulty materials or workmanship. Optional extended warranty available from Mira Customer Support.
Application
The Mira Event XS is suitable for installation as part of gravity fed plumbing systems only.
Installation - Plumbing
- The plumbing installation must comply with the requirements of UK Water Regulations / Bylaws (Scotland), Building Regulations or any particular regulations and practices specified by the local water company or water undertakers. The installation should be carried out by a plumber or contractor who is registered or is a member of an association.
- Protect the product from damage whilst making soldered connections. Some fluxes cause damage to plastic components.
- Surface mounted
- Inlet connections : 15mm dual entry push-fit inlet connections
- Supports three inlet configurations; top, bottom or back inlet supply
- Outlet connection : 1/2" BSP male
- The storage cistern should have a minimum storage capacity of 230 litres to provide adequate showering time and to comply with BS6700 (1987). Insufficient storage may result in the pump being run dry.
Electrical
- The appliance must be earthed
- This appliance is intended to be permanently connected to the fixed electrical wiring of the mains system, in accordance with the current edition of 'The Plugs and Sockets etc. (Safety) regulations in force at the time of installation
- The appliance requires a 3 Amp supply fuse
- Power supply connection; the Mira Event XS is fitted with a terminal block and earth stud which will accept cable up to 2.5mm2
- Maximum ambient temperature for the appliance whilst in use is 30°C
- The appliance will provide satisfactory performance with an incoming electricity supply voltage of 230V ± 10%. The supply voltage will affect the flow rate
- The installation must comply with 'Requirements for Electrical Installations', commonly referred to as the IEE Wiring Regulations, or any particular regulations and practices specified by the local electricity supply company.
Click to buy the Mira Event XS shower on-line now.
Click to download the Mira Event XS User Guide.
Trading Depot currently sells four Mira Event XS models on-line:
